	Kraftmessgerät Serie M7 14.000 Hz Abtastrate NEU! 500 Hz maximale Datenausgaberate Kontinuierliche Daten mit 5.000 Datenpunkt- Puffer und Bulk- Ausgang zur Erfassung Bruch Erkennung Programmierbare Fußschalter-Sequenzierung ±0,1% Genauigkeit Kapazitäten: von 0,5N bis 2500 N		Kraftmessgerät Serie M5 7.000 Hz Abtastrate NEU! 500 Hz maximale Datenausgaberate USB, RS-232, Mitutoyo, und analog Ausgang ±0,1% Genauigkeit 1.000 Messwerte Datenspeicher für Statistiken Kapazitäten: von 0,5N bis 10.000 N / 10 kN

	Kraftmessgerät Serie M4 3.000 Hz Abtastrate USB, RS-232, Mitutoyo, und analog Ausgang ±0,2% Genauigkeit 50 Messwerte Datenspeicher für Statistiken Reversierbares Gehäuse und Display Kapazitäten: von 0,5N bis 2500 N		Kraftmessgerät Serie M3 2,000 Hz Abtastrate Ultra-Kompaktes Gehäuse USB Ausgang ±0,3% Genauigkeit Reversierbares Gehäuse und Display Kapazitäten: von 0,5N bis 2500 N

	Kraftmessgerät Serie M2 500 Hz Abtastrate Ultra-Kompaktes Gehäuse ±0,5% Genauigkeit Reversierbares Gehäuse und Display Kapazitäten: von 10 N bis 2500 N

Die folgende Tabelle fasst die technischen Eigenschaften der Mark-10 Kraftmessgeräte.

	Serie M5	Serie M4	Serie M3
Accuracy (FS ±1 digit):	±0.1%	±0.2%	±0.3%
Sampling rate:	7,000 Hz	3,000 Hz	2,000 Hz
Resolution:	1/5,000	1/2,000	1/1,000
Data outputs:	USB, RS-232, Mitutoyo, Analog	USB, RS-232, Mitutoyo, Analog	USB
Programmable auto output via USB/RS-232:	Yes	No	No
MESUR^TM Lite software included:	Yes	Yes	Yes
Data output functionality:	By pressing DATA button, or requesting from a PC or other device	By pressing DATA button, or requesting from a PC or other device (currently displayed reading only)	By pressing DATA button, send current reading only. Cannot request externally.
ASCII command set for external control (Gauge Control Language 2):	Full command set	"?" only (request current reading)	None
Communication with MESUR^TMgauge and MESUR^TM Lite:	Full communication	Send data from gauge or request from software (single readings or continuous readings)	Send current (single) readings only, cannot request from software
Communication with ESM301 test stand and Series DC controllers:	Full communication, including PC control	Stop/reverse at force set points, overload protection, and communication through the “?” character only	None
Data memory:	1,000 readings with output, with individual data point deletion, or clear all	50 readings with output, with individual data point deletion, or clear all.	No
Statistics calculations and output to PC:	Yes	Yes	N/A
Averaging mode:	Yes	No	No
External trigger mode:	Yes	No	No
Analog load bar graph shown on display:	Yes	Yes	Yes
On-screen set point (pass/fail) indicators:	Yes, with markers on analog load bar graph	Yes, with markers on analog load bar graph	Yes, with markers on analog load bar graph
Display:	Graphic, backlit LCD, with backlight auto-off	Graphic, backlit LCD, with backlight auto-off	Graphic, backlit LCD, with backlight auto-off
Password protection:	Yes, for calibration and individual keys	No	No
Peak readings always displayed:	Yes	Yes	Yes
Set points:	High / low indicators, with output (dedicated pins for high and low)	High / low indicators, with output (dedicated pins for high and low)	High / low indicators, no output
Programmable audible tones (beeps):	Yes	Yes	Yes
Certificate of calibration:	NIST-traceable with data (10 points in each direction)	NIST-traceable with data (10 points in each direction)	NIST-traceable without data (data is available for an additional charge)
Configurable calibration (weight increments and no. of data points):	Yes	Yes	Yes
Overload outputs:	Dedicated pins for tension and compression	Dedicated pins for tension and compression	No
No. of units of measurement:	5	5	3
Capacity range / no. of capacities:	0.12 lbF – 1000 lbF [0.5 N - 5000 N] / 12	0.12 lbF – 500 lbF [0.5 N - 2500 N] / 11	0.12 lbF – 500 lbF [0.5 N - 2500 N] / 11
Reversible housing:	Yes	Yes	Yes
Dimensions:	2.5 x 5.9 x 1.3 in. [64 x 150 x 33 mm]	2.5 x 5.9 x 1.3 in. [64 x 150 x 33 mm]	2.5 x 3.9 x 1.5 in. [64 x 99 x 38 mm]
Preise in €

Kraft / Drehmoment Anzeigegeräte VERGLEICHSTABELLE

Die folgende Tabelle fasst die technischen Eigenschaften der Mark-10 Kraft / Drehmoment- Anzeigegeräte.

	Modell 5i	Modell 3i
Accuracy (FS ±1 digit):	±0.1%	±0.2%
Senor password protection:	Yes	No
Sampling rate:	7,000 Hz	2,000 Hz
Resolution:	1/2,000 / 1/1,000, depending on sensor	1/1,000
Data outputs:	USB, RS-232, Mitutoyo, Analog	USB
Programmable auto output via USB/RS-232:	Yes	No
MESUR^TM Lite software included:	Yes	Yes
Communication with Series DC test stand controllers:	Full communication, including PC control	None
Data Memory	Full command set	None
Communication with MESUR^TMgauge and MESUR^TM Lite:	Full communication	Send current (single) readings only, cannot request from software
Communication with ESM301 test stand and Series DC controllers:	Full communication, including PC control	None
Data memory:	1,000 readings, with output	No
Data memory deletion:	Any individual data point, or clear all	N/A
Statistics calculations and output to PC:	Yes	N/A
Averaging mode:	Yes	No
External trigger mode:	Yes	No
Analog load bar graph shown on display:	Yes	Yes
Set points (for pass/fail indication):	Yes, with high/low indicators, markers on analog load bar graph, and outputs	Yes, with high/low indicators, markers on analog load bar graph, no outputs
Display:	Graphic, backlit LCD, with backlight auto-off	Graphic, backlit LCD, with backlight auto-off
Keypad password protection:	Yes, for calibration and individual keys	No
Peak readings always displayed:	Yes	Yes
Programmable audible tones (beeps):	Yes	Yes
Certificate of calibration:	Yes, NIST-traceable with	Yes, NIST-traceable
Configurable calibration (weight increments and no. of data points):	Yes	Yes
Overload outputs:	Dedicated pins for tension and compression	No
No. of units of measurement:	5	3
Reversible housing:	Yes	No
Dimensions:	2.5 x 5.9 x 1.3 in. [64 x 150 x 33 mm]	2.5 x 3.9 x 1.5 in. [64 x 99 x 38 mm]
Preise in €

Kraftmessgeräte der Serie M7, M5, M4, M3, M2